- Placement Papers
- Interview Zone
- Resume Corner
- Contact Us
(Paper) Telco Papers Pattern (Technical & Aptitude) Part - 2
Telco Papers Pattern (Aptitude & Technical)
TELCO Paper Follows:
1.Ratio of speed of camshaft to
crankshaft in 4-stroke engine?
(a)1:2 (b)2:1 (c)1:4 (d)4:1
2.to change the dir. of rotation of 3 phase induction moterwe have to change?
3.why we make initially star-connection then
delta-connection? 4.H8/f8 shows?
(a)clearence fit (b)shrink fit (c)interference fit
5.centipoise is the unit of?
(a)hardness (b) viscosity
6.brinnel no. is the unit of?
(a)hardness (b) viscosity
7. hardness is?
(a)resistance to deform (b)resistance to machining (c)resistance to abbration
8.moudoulus of elasticity of mild steel?
(a)2.2*(10**6) (b)3*(10**6) (c)2.2*(10**5)
9.co-efficiant of friction for mild steel & cast iron?
(a).3 (b).1 (c).01 (d).5
10.in vechile cluch is used between?
11.in metric thread the angle is?
(a)45 (b)55 (c)30
12.in lathe(lead screw) the thread is used is?
13.idler pully is used?
(a)low load,high speed (b)high load low speed
14.in which operation tool rotates and work piece moves linearly?
(a) milling (b)turning
15.broaching is the process of?
(a)finishing hole (b)making hole (c)splines (d)keyway
(a)harden core (b)harden surface (c)soften surface
17.in sumerged arc welding why filler is kept in the molten material?\ ans-to prevent oxydising the upper surface
18.the thermal efficiency of C.I engine?
(a)ans-around 30% (B)around 15%
19.in C.I engine after compression stroke?
(a)ans-only fule is injected (b)mixture is injected (c)air is injected
20.twist drill is specified by?
(a)flute& dia (b)twist angle&dia
21.the reduction speed ratio of spur gear is?
(a)20:1 (b)2:1 (c)
22.luminious is unit of?
23.carbide tool is used for?
(a)high speed (b)low speed (c)all speed (d) medium speed
24.+ve back rake is used for?
(a)Al (b)mild steel (d)cast iron
25.acid rain occurs due to this exhaust from C.I engine?
26.which machin is rested support?
27.anmneling is used for?
(a)softening (b)remove stress
28.in cantilever beam if force is increased an non supported end chance of failure is?
(a)anywhere (b)middle (c)near wall side
29.in simple supported beam when force is acting at middle, max. deflection is??
30.surge pump is used in pipe line for??
31.E=2000kg/mm*2, stress=200 kg/cm*2, length l=200mm, dia.=40mm then channge in length=?
32.in two gear system moudle,teeth of one gear,speed of both gear is given.you have to calculate center distance?
33.the thickness of mild steel is given,you have to create a hole(dia. is given,speed of something is given=22m/min.you have to calculate another speed perhaps cutting speed in rpm.??
34.3 coplanner fore are ,angle betwwen P & R is 90.P & Q is 120.if Q=20 then.P=?
35.two of same mass.first is inside the water by 1/2 volume other by 2/3 volume.what is ratio of their densities?
SOME MORE APTI QUESTIONS(SOME OF THEM MIGHT BE SAME)
paper (M. Tech)
1)Youngs modulus of mild steel 2.2* 10^6kg/cm2
2)rod of dia(given)length(given)subjected to stress(given) and "E"(given). what is increase in length. 0.2cm
3)centipose is unit of........... viscosity
4)hardness is measured in brinell no.
5)steady rest is used in....... i) milling ii)lathe (2 more option)
6)rotating cutter and sliding w/p(process is)
deflection of beam supported at two ends and loaded at centre
beam failure occurs at ...... support
type of fit is H9f9
finish is represented by....
iii)rectangle ....none of these
is done to produce....
ii)splines...(2 more options)
drill is specified by
ii)lip angle , material,dia
iii)dia ,shank, material
13)in diesel engine.. injection occurs ..
ii)20 degree atdc
iii)12 degree atdc...
4-stroke engine ratio of cam shaft and crank shaft rotation i)1:2 ii)2:1 ....etc
gears ...one(driving) at 100 rpm and other 300 rpm....driven has m=4 and no. of
teeth 60 distance b/w centre is....
ratio ofspur gear
i)1:4 ii) 1:20 iii)1:10.....
carbide tool is used at..... low , medium , high or all speed
18)hardness signify....resistence to. scratching machining etc
19)coefficient of friction between cast iron and mild steel....
i)0.2 ii) 0.3 ii) 0.001 etc.
SAW arc is struck under flux
i)to prevent oxidation..(3 more options)
test is used for non ferrous material weld... magnetic particle test
is located between..... engine and gear box
efficiency of diesel engine is....
i)less than 20% ii)less than 30%...etc
24)in CI engine injection takes place ... at the end of compression stroke
25)clearence volume(given)...suction volume(given) what is compression ratio.
26)what type of sress is hertz stress.
i)tensile ii) shear iii)contact....
helical spring is arranged in parallel ...the stiffness is ans- sum of stiffness
ans- < 3* (sigma)
29)two cube ..one is half submerged and other is 2/3 submerged ?. Ratio of their densities?.
30)for ammonia HP per tonn of refrigeration
31) model of pump of 20 HP ?.rotates at 400 rpm (head is 20m) find out speed when head is 60 m( given model dia is ? of original)